How Does pH Affect Precipitation?
At a glance
- 1. Write the equilibrium
Identify the solid and write its solubility-product expression.
- 2. Track pH-sensitive ions
Determine whether pH changes hydroxide or the concentration of an anion that forms the solid.
- 3. Compare Q with Ksp
Use current ion concentrations to decide whether the solution is undersaturated, saturated, or supersaturated.
- 4. Check for exceptions
Consider complex formation, amphoteric behavior, and whether equilibrium has been reached.
Changing pH can make a solution form a solid or make an existing solid dissolve. The effect depends on which ions form the solid and how their concentrations respond to pH; there is no rule that raising pH always causes precipitation.
The most familiar case is a metal hydroxide: raising pH increases the hydroxide-ion concentration and can push the solution past the point of saturation. To predict what happens in a particular solution, identify the solid and compare its ion product with its solubility product.
The key idea: compare Q with Ksp
For a sparingly soluble solid, its solubility product, , describes the equilibrium between the solid and its dissolved ions. For example:
The corresponding ion product is
Compare with under the same conditions:
- If , the solution is unsaturated; more solid can dissolve.
- If , the solution is at saturation and in equilibrium with the solid.
- If , precipitation is thermodynamically favored until the dissolved concentrations decrease.
Strictly, thermodynamic expressions use ion activities. Concentrations are often adequate for introductory calculations in dilute solutions.
Why raising pH often precipitates metal hydroxides
At about 25 °C, . As pH rises, pOH falls and rises. Because hydroxide appears in the ion product, this can increase enough to exceed .
For a metal hydroxide , the saturation condition is
The hydroxide concentration is raised to the power , so the saturation point can be quite sensitive to pH. The exact pH at which precipitation begins also depends on the metal-ion concentration: a solution with more dissolved metal can reach saturation at a lower pH.
Worked example: magnesium hydroxide
Suppose a solution contains magnesium ions. Use for at 25 °C. At the onset of precipitation, take as approximately and set :
Under these assumptions, precipitation starts near pH 9.37. At pH 10, , giving an initial ion product of , greater than . Magnesium hydroxide is therefore expected to precipitate. This estimate neglects activity effects and treats the dissolved magnesium concentration as unchanged right at the onset; actual conditions can shift the threshold.
When pH changes other precipitates
Many precipitates contain an anion that is the conjugate base of a weak acid. Raising pH converts more of that acid into the anion, which may favor a solid containing it. For example, higher pH can increase the carbonate fraction of dissolved inorganic carbon, potentially promoting precipitation of metal carbonates. Lowering pH shifts carbonate toward bicarbonate and dissolved carbon dioxide, and can dissolve a carbonate solid.
The same general reasoning applies to sulfides and phosphates, though their acid-base equilibria involve multiple forms. For a metal sulfide, the amount of sulfide ion available depends on pH; for a phosphate solid, the proportions of phosphate species also change with pH. A reliable prediction requires accounting for those species rather than treating the total concentration of the acid or its anions as if it were all in one form.
Important exceptions and common mistakes
Amphoteric hydroxides can dissolve at high pH. Solids such as aluminum hydroxide and zinc hydroxide can dissolve in sufficiently basic solution by forming soluble hydroxo complexes. Their behavior may be: dissolved at low pH, precipitated over an intermediate pH range, then dissolved again at high pH. Thus, “higher pH means more hydroxide precipitate” is not universally true.
Other ligands affect free-metal concentration. Ammonia, cyanide, and other ligands can bind metal ions in solution. This lowers the free available for the solubility-product expression and may suppress precipitation. A pH change can also alter how strongly a ligand binds.
Do not confuse total concentration with the concentration of the relevant ion. For example, total dissolved carbonate is not the same as , and total dissolved metal is not always the same as free metal-ion concentration. Acid-base and complex-formation equilibria determine the relevant concentrations.
Supersaturation does not guarantee an immediate visible solid. Precipitation can be delayed while nuclei form, and very small particles may remain suspended. indicates a thermodynamic drive to precipitate, not necessarily an instantaneous observable change.
For a specific mixture, write the solid’s dissolution equation, determine the pH-dependent concentrations of its ions, and calculate . Then check whether complexation or amphoteric behavior changes the result.
References
- Daniel C. Harris, Quantitative Chemical Analysis
- Werner Stumm and James J. Morgan, Aquatic Chemistry
Spotted an error? Send a correction. Read how we write and check articles in our editorial policy.