Ph · Physics

Wave Equation vs. Helmholtz Equation: What Is the Difference?

Published By the 9to5Science editorial team

At a glance

  1. 1. Identify the variables

    The wave equation describes dependence on both position and time; the Helmholtz equation normally describes spatial dependence at one frequency.

  2. 2. Assume harmonic time

    Represent the field with a sinusoidal time factor and substitute it into the wave equation.

  3. 3. Define the wavenumber

    Set k equal to angular frequency divided by wave speed, producing the Helmholtz equation.

  4. 4. Check the limitations

    A single Helmholtz solution represents one frequency, not an arbitrary time-dependent wave.

Advertisement

The wave equation and the Helmholtz equation are closely related, but they do not describe exactly the same mathematical problem. The wave equation keeps time as an independent variable, whereas the Helmholtz equation usually describes the spatial pattern of a field oscillating at one specified angular frequency.

The Helmholtz equation is therefore best understood as a frequency-domain or separated-variable form of the wave equation—not as a completely different physical law.

The wave equation

For a scalar field u(r,t)u(\mathbf r,t) propagating through a uniform, nondispersive medium with constant wave speed vv, the source-free wave equation is

∇2u−1v2∂2u∂t2=0.\nabla^2 u-\frac{1}{v^2}\frac{\partial^2 u}{\partial t^2}=0.

Here, ∇2\nabla^2 describes how the field varies in space, while the second time derivative describes its temporal evolution. The function uu could represent a displacement, pressure variation, electric-field component, or another approximately scalar wave quantity.

In one spatial dimension, the equation becomes

∂2u∂x2−1v2∂2u∂t2=0.\frac{\partial^2u}{\partial x^2}-\frac{1}{v^2}\frac{\partial^2u}{\partial t^2}=0.

Its general solution is

u(x,t)=f(x−vt)+g(x+vt),u(x,t)=f(x-vt)+g(x+vt),

where ff and gg are arbitrary functions. The first term travels in the positive xx direction and the second travels in the negative xx direction.

This form shows why the wave equation is more general than a single sinusoidal wave. It can describe pulses, wave packets, transients, and arbitrary initial conditions.

The Helmholtz equation

The source-free scalar Helmholtz equation is

∇2ψ+k2ψ=0,\nabla^2\psi+k^2\psi=0,

where ψ(r)\psi(\mathbf r) depends on position but not explicitly on time. The quantity kk is the wavenumber. In a uniform, nondispersive medium described by this constant-speed wave equation,

k=ωv=2πλ,k=\frac{\omega}{v}=\frac{2\pi}{\lambda},

with angular frequency ω\omega and wavelength λ\lambda.

The Helmholtz equation can also appear as an eigenvalue equation. In that setting, k2k^2 is an eigenvalue determined by the geometry and boundary conditions. For example, only certain values of kk may be allowed inside a cavity or along a bounded string.

How one follows from the other

Suppose the field has a single-frequency, sinusoidal time dependence. Write it as

u(r,t)=Re⁡{ψ(r)e−iωt}.u(\mathbf r,t)=\operatorname{Re}\left\{\psi(\mathbf r)e^{-i\omega t}\right\}.

The complex exponential is a convenient notation; the physical field is its real part. Differentiating twice with respect to time gives

∂2u∂t2=Re⁡{−ω2ψ(r)e−iωt}.\frac{\partial^2u}{\partial t^2} =\operatorname{Re}\left\{-\omega^2\psi(\mathbf r)e^{-i\omega t}\right\}.

Substitute this into the wave equation:

∇2(ψe−iωt)−1v2∂2∂t2(ψe−iωt)=0.\nabla^2\left(\psi e^{-i\omega t}\right) -\frac{1}{v^2}\frac{\partial^2}{\partial t^2} \left(\psi e^{-i\omega t}\right)=0.

Since the time factor is common to both terms,

(∇2ψ+ω2v2ψ)e−iωt=0.\left(\nabla^2\psi+\frac{\omega^2}{v^2}\psi\right)e^{-i\omega t}=0.

Therefore,

∇2ψ+k2ψ=0,k=ωv.\nabla^2\psi+k^2\psi=0, \qquad k=\frac{\omega}{v}.

This is the Helmholtz equation.

The same result follows by separation of variables. If u(r,t)=ψ(r)T(t)u(\mathbf r,t)=\psi(\mathbf r)T(t), substitution into the wave equation leads to a spatial equation and a time equation. Choosing the separation constant as k2k^2 gives

∇2ψ+k2ψ=0\nabla^2\psi+k^2\psi=0

and

d2Tdt2+ω2T=0,ω=vk.\frac{d^2T}{dt^2}+\omega^2T=0, \qquad \omega=vk.

Worked example: a traveling sinusoidal wave

Consider the one-dimensional wave

u(x,t)=Acos⁡(kx−ωt).u(x,t)=A\cos(kx-\omega t).

Its spatial second derivative is

∂2u∂x2=−k2Acos⁡(kx−ωt)=−k2u,\frac{\partial^2u}{\partial x^2}=-k^2A\cos(kx-\omega t)=-k^2u,

and its time second derivative is

∂2u∂t2=−ω2Acos⁡(kx−ωt)=−ω2u.\frac{\partial^2u}{\partial t^2}=-\omega^2A\cos(kx-\omega t)=-\omega^2u.

Putting these into the wave equation gives

−k2u+ω2v2u=0.-k^2u+\frac{\omega^2}{v^2}u=0.

Thus the wave is a solution when

ω=vk.\omega=vk.

If you remove the time factor and retain the spatial complex amplitude ψ(x)=Aeikx\psi(x)=Ae^{ikx}, then

d2ψdx2+k2ψ=0,\frac{d^2\psi}{dx^2}+k^2\psi=0,

which is the one-dimensional Helmholtz equation.

For a numerical example, let v=340 m/sv=340\ \mathrm{m/s} and f=170 Hzf=170\ \mathrm{Hz}. Then ω=2πf\omega=2\pi f and

λ=vf=2 m,k=2πλ=π rad/m.\lambda=\frac{v}{f}=2\ \mathrm{m}, \qquad k=\frac{2\pi}{\lambda}=\pi\ \mathrm{rad/m}.

The corresponding time-dependent wave is Acos⁡(πx−340πt)A\cos(\pi x-340\pi t), while its spatial Helmholtz amplitude is proportional to eiπxe^{i\pi x}.

The main practical difference

FeatureWave equationHelmholtz equation
Independent variablesSpace and timeUsually space only
FrequenciesArbitrary or many frequenciesOne specified frequency or eigenfrequency
Typical usePulses, transients, propagation, initial-value problemsSteady-state sinusoidal fields, resonances, scattering
Outputu(r,t)u(\mathbf r,t)Spatial amplitude ψ(r)\psi(\mathbf r)
Time informationExplicitly retainedEncoded through a factor such as e−iωte^{-i\omega t}

A general time-dependent solution can be built by superposing Helmholtz solutions at different frequencies. Fourier analysis expresses this idea as

u(r,t)=∫−∞∞ψω(r)e−iωt dω,u(\mathbf r,t)=\int_{-\infty}^{\infty}\psi_\omega(\mathbf r)e^{-i\omega t}\,d\omega,

with suitable normalization. One Helmholtz problem gives only one frequency component; the full wave may require many components.

Sources and sign conventions

With the convention e−iωte^{-i\omega t}, the source-free equation has the form

∇2ψ+k2ψ=0.\nabla^2\psi+k^2\psi=0.

Using e+iωte^{+i\omega t} instead changes the complex representation of traveling waves but not the physical result. A source term produces an inhomogeneous Helmholtz equation, for example

∇2ψ+k2ψ=−s(r),\nabla^2\psi+k^2\psi=-s(\mathbf r),

where the exact sign and normalization depend on how the source is defined.

For electromagnetic fields, Maxwell’s equations lead to vector wave equations. In a homogeneous, isotropic, source-free medium, each Cartesian field component often satisfies a scalar Helmholtz equation, but boundaries, material variation, polarization, and interfaces can require the full vector formulation.

Common mistakes

  • Treating the Helmholtz equation as fully time dependent. Its unknown is normally a spatial amplitude. Add the time factor to reconstruct the physical harmonic field.
  • Using one Helmholtz solution for a pulse. A pulse contains a range of frequencies and generally requires superposition.
  • Confusing kk with frequency. The wavenumber is k=2π/λk=2\pi/\lambda; angular frequency is ω=2πf\omega=2\pi f. They are related by ω=vk\omega=vk when vv is a frequency-independent wave speed, as in the simple nondispersive model; in a dispersive medium, the phase velocity and kk generally depend on frequency.
  • Ignoring boundary conditions. The differential equation alone does not determine a unique field. Sources, initial data, and boundary or radiation conditions are also needed.
  • Assuming every separated solution is a traveling wave. A Helmholtz solution can represent a traveling wave, a standing wave, a resonant mode, or a scattered field, depending on the boundary conditions and combination of solutions.

References

  1. Introduction to Electrodynamics, David J. Griffiths
  2. Mathematical Methods for Physicists, George B. Arfken, Hans J. Weber, and Frank E. Harris

Spotted an error? Send a correction. Read how we write and check articles in our editorial policy.