Ma · Mathematics

How to Find the Volume of a Vase with Calculus

Published By the 9to5Science editorial team

At a glance

  1. 1. Choose the profile

    Describe the vase’s inside radius as a function of height, using measurements or a given polynomial.

  2. 2. Set the limits

    Integrate from the inside bottom to the fillable height; use the inside profile for capacity.

  3. 3. Use cross-sections

    For a vase symmetric about its vertical axis, each horizontal slice has area pi times radius squared.

  4. 4. Evaluate and check

    Integrate the squared radius, multiply by pi, and report cubic units.

Try it: Volume calculator

To find the volume a vase can hold, model its inside wall as a curve and add up the areas of thin horizontal circular slices. This is the disk method, a direct application of definite integration. The result is the vase’s interior capacity, provided the vase is rotationally symmetric about its vertical axis.

The title gives no particular dimensions or radius function, so the method below is general and includes a worked example with a chosen polynomial profile.

The volume formula

Let yy measure height from the inside bottom of the vase, and let r(y)r(y) be its inside radius at height yy. A thin slice of thickness dydy is approximately a disk of area πr(y)2\pi r(y)^2. Its volume is approximately πr(y)2dy\pi r(y)^2dy. Adding these slices from the bottom, y=ay=a, to the top, y=by=b, gives

V=π∫abr(y)2 dy.V=\pi\int_a^b r(y)^2\,dy.

The radius must be measured from the axis of symmetry to the inside wall. If the profile is given as a diameter d(y)d(y) rather than a radius, use r(y)=d(y)/2r(y)=d(y)/2, so the cross-sectional area is πd(y)2/4\pi d(y)^2/4.

If the vase’s wall thickness matters, let R(y)R(y) denote the outside radius and r(y)r(y) the inside radius. The material in a horizontal slice is a washer, so the volume of the ceramic or glass is

Vmaterial=π∫ab(R(y)2−r(y)2) dy.V_{\text{material}}=\pi\int_a^b\left(R(y)^2-r(y)^2\right)\,dy.

This is different from capacity: capacity uses only the interior space.

Worked example with a polynomial profile

Suppose a vase is rotationally symmetric, has an inside height of 22 cm, and its inside radius is modeled by

r(y)=1+y24,0≤y≤2,r(y)=1+\frac{y^2}{4},\qquad 0\le y\le 2,

where yy is measured in centimeters. The radius grows from 11 cm at the bottom to 22 cm at the top. The capacity is

V=π∫02(1+y24)2 dy=π∫02(1+y22+y416) dy=π[y+y36+y580]02=π(2+86+3280)=56π15 cm3.\begin{aligned} V&=\pi\int_0^2\left(1+\frac{y^2}{4}\right)^2\,dy\\ &=\pi\int_0^2\left(1+\frac{y^2}{2}+\frac{y^4}{16}\right)\,dy\\ &=\pi\left[y+\frac{y^3}{6}+\frac{y^5}{80}\right]_0^2\\ &=\pi\left(2+\frac{8}{6}+\frac{32}{80}\right)\\ &=\frac{56\pi}{15}\ \text{cm}^3. \end{aligned}

Numerically, this is about 11.73 cm311.73\ \text{cm}^3. The result is plausible: the vase’s cross-sectional area is between π\pi and 4π4\pi square centimeters over a height of 22 cm, so its volume must be between 2π2\pi and 8π8\pi cubic centimeters. The calculated value lies in that range.

How to get the radius function

Sometimes a problem supplies a polynomial profile directly. If it instead gives the vase’s outline as a graph, check which coordinate represents height and which represents horizontal distance from the axis. For example, if the outline is written as x=f(y)x=f(y) with the vase’s axis along the yy-axis, then the radius is r(y)=f(y)r(y)=f(y), assuming the curve describes the inside wall.

For a real vase, you can measure the inside radius at several heights and fit a polynomial or another suitable curve. Then integrate the square of that model over the height you want to fill. A fitted curve is an approximation, so the calculated capacity is also approximate. Do not use a model outside the range of measured heights unless you have a reason to trust its behavior there.

If the vase’s shape is not rotationally symmetric, the circular-slice formula does not apply as written. You need the actual cross-sectional areas as functions of height, using V=∫abA(y) dyV=\int_a^b A(y)\,dy, or a three-dimensional model of the interior.

Common mistakes

  • Using the outside radius for capacity: This counts the wall material and overestimates how much liquid the vase holds. Use the inside radius.
  • Forgetting to square the radius: A circular slice has area πr2\pi r^2, not 2πr2\pi r; the latter is the circumference.
  • Confusing radius and diameter: A diameter must be halved before using the disk formula.
  • Integrating over the wrong height: The limits should run from the inside bottom to the fillable top. A thick base or neck may make these differ from the vase’s overall height.
  • Mixing units: If radius and height are measured in centimeters, the result is in cubic centimeters; if they are in inches, it is in cubic inches.
  • Assuming a vase is a solid object: The integral of the outside profile gives the volume enclosed by the outside surface, not the amount of material. Subtract the interior volume to find material volume.

Spotted an error? Send a correction. Read how we write and check articles in our editorial policy.