Ph · Physics

What Is the Shape of the Graph of V = E − rI?

Published By the 9to5Science editorial team

At a glance

  1. 1. Identify the variables

    Plot terminal voltage V on the vertical axis and current I on the horizontal axis.

  2. 2. Read the slope

    The coefficient of I is −r, so the graph is a straight line that slopes downward.

  3. 3. Find the intercepts

    At zero current, V equals E; at zero voltage, I equals E divided by r.

  4. 4. Check the assumptions

    The line applies when emf and internal resistance stay constant and current follows the discharge sign convention.

The equation V=−rI+EV = -rI + E, also written V=E−rIV = E-rI, describes the terminal voltage of a source such as a battery while it delivers current. If you put current II on the horizontal axis and terminal voltage VV on the vertical axis, the graph is a straight line that slopes downward when the internal resistance rr is positive.

The line’s vertical intercept is the emf EE, and its slope is −r-r. This relationship holds when the source’s emf and internal resistance can be treated as constant over the range of currents being measured.

Read the equation as a line

A straight-line equation has the form y=mx+by=mx+b, where mm is the slope and bb is the vertical-axis intercept. Comparing it with

V=(−r)I+E,V=(-r)I+E,

you can identify:

  • Vertical variable: terminal voltage VV.
  • Horizontal variable: current II.
  • Slope: −r-r.
  • Vertical intercept: EE.

The slope is negative because the source loses some voltage inside its own internal resistance as it supplies more current. In this model, the terminal voltage is the emf minus the internal voltage drop rIrI.

The units also check out: rr is measured in ohms, and rIrI has units of volts because 1 Ω⋅1 A=1 V1\,\Omega\cdot 1\,\mathrm{A}=1\,\mathrm{V}.

Find the intercepts

Set I=0I=0 to find where the line meets the vertical axis:

V=E−r(0)=E.V=E-r(0)=E.

Thus, the open-circuit voltage—the voltage when no current is drawn—is EE in this idealized model.

To find where the line meets the horizontal axis, set V=0V=0:

0=E−rI⟹I=Er.0=E-rI \qquad\Longrightarrow\qquad I=\frac{E}{r}.

This is the model’s short-circuit current. A real battery should not be deliberately shorted: the resulting current can cause heating, damage, or injury, and the simple model may not remain accurate at such a large current.

Worked example

Suppose a source has emf E=12 VE=12\,\mathrm{V} and internal resistance r=0.50 Ωr=0.50\,\Omega. Its terminal voltage is

V=12−(0.50)I,V=12-(0.50)I,

where II is in amperes and VV is in volts. Several points on the graph are:

Current II (A)Terminal voltage VV (V)
012
410
126
240

Plot these points with II horizontally and VV vertically, then draw a straight line through them. The line begins at (0,12)(0,12) and has slope −0.50 V/A=−0.50 Ω-0.50\,\mathrm{V/A}=-0.50\,\Omega. Its horizontal intercept is I=12/0.50=24 AI=12/0.50=24\,\mathrm{A}, the predicted short-circuit current in the model.

What the slope tells you

If you measure terminal voltage at several currents and the points lie approximately on a straight line, the slope estimates the negative of the internal resistance. For two points (I1,V1)(I_1,V_1) and (I2,V2)(I_2,V_2),

slope=V2−V1I2−I1=−r.\text{slope}=\frac{V_2-V_1}{I_2-I_1}=-r.

Therefore, rr is the positive magnitude of that slope. Experimental data may not fall exactly on a line because of measurement uncertainty or because a battery’s behavior changes with temperature, state of charge, or current.

Common mistakes

  • Reversing the axes: The slope is −r-r only when VV is plotted vertically against II horizontally. If you plot II against VV, rearrange the equation to get I=E/r−V/rI=E/r-V/r; the slope is then −1/r-1/r.
  • Calling EE the terminal voltage at every current: EE is the zero-current intercept in this model. During discharge, terminal voltage is lower by rIrI.
  • Dropping the minus sign: A positive internal resistance gives a negative slope for a source delivering current.
  • Treating the line as universal: The equation assumes constant EE and rr and uses the usual convention that discharge current is positive. During charging, current may be assigned the opposite sign, so the terminal-voltage relation is written with a corresponding sign change.

References

  1. OpenStax, University Physics Volume 2: Electromotive Force: Terminal Voltage

Spotted an error? Send a correction. Read how we write and check articles in our editorial policy.