Ph · Physics

How to Find the Distance Between Two Packages in Free Fall

Published By the 9to5Science editorial team

At a glance

  1. 1. Set the starting positions

    Record each package’s initial position and the time it is released.

  2. 2. Choose a direction

    Take upward as positive and use the same coordinate system for both packages.

  3. 3. Write each motion equation

    Use constant-acceleration motion with acceleration approximately −9.8 m/s² near Earth.

  4. 4. Subtract positions

    The distance between the packages is the absolute value of their position difference.

The distance between two packages depends on where and how they start moving. The title alone does not specify their initial separation, release times, or velocities, so it cannot determine one numerical answer. A common interpretation is that the packages are falling freely near Earth; in that case, you can find their separation by comparing their positions at the same time.

The key idea: compare the motions

Choose a vertical coordinate, such as upward as positive. Near Earth’s surface, ignoring air resistance, each freely falling package has acceleration a=−ga=-g, where g≈9.8 m/s2g\approx 9.8\,\text{m/s}^2. The position of package ii after a time tt measured from a shared starting time is

yi(t)=yi,0+vi,0t−12gt2.y_i(t)=y_{i,0}+v_{i,0}t-\frac{1}{2}gt^2.

Here, yi,0y_{i,0} is its initial height and vi,0v_{i,0} is its initial vertical velocity. The distance between the packages at that instant is

d(t)=∣y2(t)−y1(t)∣.d(t)=|y_2(t)-y_1(t)|.

Subtracting the position equations gives

y2(t)−y1(t)=(y2,0−y1,0)+(v2,0−v1,0)t.y_2(t)-y_1(t)=(y_{2,0}-y_{1,0})+(v_{2,0}-v_{1,0})t.

The gravity terms cancel because both packages have the same acceleration. Thus, if both are released simultaneously with the same initial velocity, their separation stays constant while they fall. Gravity makes each package speed up, but it does not make one catch the other.

The vertical origin is arbitrary; in the examples below, assume the ground is below all the positions calculated, so the packages remain in free fall for the stated intervals.

Worked example: released together

Suppose one package is 12 m above the other, and both are released from rest at the same time. Let the lower package start at height y1,0=0y_{1,0}=0 and the upper one at height y2,0=12 my_{2,0}=12\,\text{m}. Both have initial velocity zero.

After 1 second, their positions are

y1(1)=0−12(9.8)(1)2=−4.9 m,y2(1)=12−12(9.8)(1)2=7.1 m.\begin{aligned} y_1(1)&=0-\frac{1}{2}(9.8)(1)^2=-4.9\,\text{m},\\ y_2(1)&=12-\frac{1}{2}(9.8)(1)^2=7.1\,\text{m}. \end{aligned}

Their separation is ∣7.1−(−4.9)∣=12 m|7.1-(-4.9)|=12\,\text{m}, the same as at the start. In a real situation, a package may hit the ground before a later time; the constant-gap result applies only while both packages are in free fall.

If the packages are released at different times

A delayed release changes the result because the packages are not both accelerating downward over the same time interval. For example, suppose the upper package is released from rest 1 second after the lower one. Let tt be the time in seconds since the lower package was released, and let the lower package start at height zero. For t≥1t\geq 1, their positions are

y1(t)=−12gt2,y2(t)=12−12g(t−1)2.\begin{aligned} y_1(t)&=-\frac{1}{2}gt^2,\\ y_2(t)&=12-\frac{1}{2}g(t-1)^2. \end{aligned}

At t=2 st=2\,\text{s}, the lower package has fallen for 2 seconds and the upper package for 1 second:

y1(2)=−19.6 m,y2(2)=12−4.9=7.1 m.\begin{aligned} y_1(2)&=-19.6\,\text{m},\\ y_2(2)&=12-4.9=7.1\,\text{m}. \end{aligned}

Their separation is ∣7.1−(−19.6)∣=26.7 m|7.1-(-19.6)|=26.7\,\text{m}. The upper package has had less time to fall, so the gap has grown. This example assumes both packages start at rest and uses the same constant value of gg for each.

More generally, if package 1 is released at time t1t_1 and package 2 at time t2t_2, use each package’s own elapsed time: τi=t−ti\tau_i=t-t_i. Once it has been released, its position is

yi(t)=yi,0+vi,0τi−12gτi2.y_i(t)=y_{i,0}+v_{i,0}\tau_i-\frac{1}{2}g\tau_i^2.

Then subtract the two positions and take the absolute value. Do not use one elapsed time for both packages when their release times differ.

Common mistakes

  • Assuming gravity changes the gap between identical falling objects. If their initial vertical velocities match and they are released together, their relative acceleration is zero, so their separation remains constant.
  • Subtracting heights without checking which is higher. The signed difference can be negative; distance is the absolute value.
  • Mixing release times. Each package’s motion equation must use the time since that package was released.
  • Ignoring the ground or air resistance. Once one package lands, it no longer follows the free-fall equation. Significant air resistance can also give packages different accelerations.

If the question means gravitational attraction

Sometimes “distance between two packages” means finding their separation from their masses and the gravitational force between them. Newton’s law is

F=Gm1m2r2,F=G\frac{m_1m_2}{r^2},

where m1m_1 and m2m_2 are the masses and rr is the distance between their centers. Rearranging gives r=Gm1m2/Fr=\sqrt{Gm_1m_2/F}. That calculation requires the masses and the force; it is different from calculating how far apart falling packages are. For ordinary packages, Earth’s gravity dominates their motion, while their mutual attraction is usually negligible.

References

  1. OpenStax, University Physics Volume 1: Motion Along a Straight Line
  2. OpenStax, University Physics Volume 1: Newton’s Law of Universal Gravitation

Spotted an error? Send a correction. Read how we write and check articles in our editorial policy.