How to Fix “Misplaced Alignment” Errors in TeXmaker
At a glance
- 1. Read the first error
Find the first LaTeX error in Texmaker’s log and note the line number it reports.
- 2. Locate the ampersand
Check that each unescaped & is inside a table or another alignment environment.
- 3. Escape text ampersands
Write \& when you want a literal ampersand in ordinary text or a table cell.
- 4. Check table columns
Make sure each table row has the right number of cells for its column specification.
Texmaker is an editor: the error comes from the LaTeX compiler it runs. The message Misplaced alignment tab character & means LaTeX found an & where it was not expecting a column separator. The usual fix is to escape a literal ampersand as \& or put the alignment marker inside the appropriate environment.
What & means in LaTeX
Inside alignment environments such as tabular, array, and align, an unescaped & separates columns or aligned parts. In ordinary text, an unescaped & is not a printable ampersand; LaTeX interprets it as an alignment marker and raises an error if there is no active alignment.
For example, this text causes the error:
Research & Development
Write Research \& Development instead. The same rule applies in table cells: use \& when the ampersand is part of the cell’s wording rather than a separator between cells.
Fix the error step by step
- Look at the first error in the log. In Texmaker, check the messages shown after compilation and open the relevant source line. Fix the first LaTeX error before chasing later ones; subsequent messages can be consequences of the first problem.
- Inspect every
&near that line. Ask whether it separates table columns or aligned equations. If it is meant to print as text, put a backslash before it:\&. - Check the surrounding environment. A column separator belongs inside a structure that defines columns, such as
tabular, or an alignment environment such asalign. A stray&before or after that environment is still an error. - Check the table’s column count. If a table has three columns, each ordinary row should contain two unescaped
&separators. An extra separator often produces a different message, such asExtra alignment tab has been changed to \cr. - Compile again. If the error remains, inspect the reported line and a few lines before it. An unclosed brace or environment earlier in the file can make LaTeX interpret a later
&in the wrong context.
Worked example: an ampersand in a table
Here is a complete document that compiles. The & between each pair of cells divides the table into two columns. The ampersand in “Research & Development” is escaped because it is part of the cell’s text.
\documentclass{article}
\begin{document}
\begin{tabular}{ll}
Department & Location \\
Research \& Development & Building A \\
Sales & Building B \\
\end{tabular}
\end{document}
The column specification {ll} declares two left-aligned columns. Each row therefore needs one unescaped & to separate its two cells. In the second row, \& prints a literal ampersand within the first cell; it does not start another cell.
The same distinction applies in aligned equations. For example, inside an align environment, & marks the point at which equations should line up. Outside that environment, use \& for a printed ampersand.
Common mistakes
- Escaping the wrong ampersand: Do not escape the separators that divide table cells. Escape only an ampersand you want printed as text.
- Putting table separators in prose: A line such as
A & Bin a paragraph is invalid. UseA \& Bunless the text is genuinely inside an alignment environment. - Adding too many cells: A three-column row needs two separators, not three. A mistaken extra
&can shift cells or trigger a separate alignment error. - Assuming the reported line is the only cause: TeX’s line reference is useful, but an earlier missing brace or
\end{...}can disrupt how later characters are interpreted. Check the first error and the nearby structure. - Treating Texmaker as the cause: Changing editors usually will not fix a LaTeX syntax error. Correct the source and compile it again.
If you cannot identify the stray marker, temporarily remove or comment out nearby table rows, then restore them a few at a time. This can help isolate the first row or text fragment that introduces the unexpected &.
References
- LaTeX: A Document Preparation System, Leslie Lamport
Spotted an error? Send a correction. Read how we write and check articles in our editorial policy.